Veteran-Owned Engineering Firm

Hardware-grade security for a post-quantum world.

◆ Veteran-Owned Small Business ◆ SAM.gov Registered ◆ Post-Quantum FPGA IP

K-Fam LLC designs electrical and firmware systems for IoT, medical, and SaaS products — with a specialty in NIST post-quantum cryptography implemented directly in silicon.

unified_pqc_core.sv
// Dual-modulus arithmetic datapath
module unified_pqc_core #(
  parameter SEC_LEVEL = 5 // 1/3/5
) (input clk_100mhz,
   axi_stream.slave eth_rx);
 
  ML_KEM kem // FIPS 203
  ML_DSA dsa // FIPS 204
  KECCAK hash // FIPS 202
 
endmodule // timing: CLOSED
100 MHz
Timing closure on Arty A7-100T
60/60
NIST ACVP conformance cases passed
3×
Peer-reviewed publications
1 core
ML-KEM + ML-DSA, all NIST levels
What We Do

Embedded expertise, from board to bitstream.

Full-stack electrical engineering under one roof — firmware, hardware, systems, test, and PCB layout — backed by active doctoral research in cryptographic hardware.

Firmware & Hardware

Embedded firmware, board bring-up, RTL, and PCB layout for products that have to work in the field — not just on the bench.

Post-Quantum Cryptography

FIPS 203/204 key encapsulation and digital signatures implemented in FPGA fabric, with side-channel hardening and ACVP validation.

Regulated Systems

Design and consulting for medical and industrial products where traceability, test coverage, and documentation are non-negotiable.

Engagement Models

Three ways to work with K-Fam.

Structured for teams that need deep embedded expertise without a full-time hire — or a defensible cryptographic IP block they can license.

Tier 01 · Retainer

Fractional Hardware & Embedded

A senior R&D engineer embedded in your team on a recurring retainer — covering firmware, hardware, systems, test, and PCB layout as your roadmap demands.

  • Board bring-up and debug
  • Firmware architecture & review
  • Design-for-test and validation
  • Vendor and BOM support
Tier 02 · Consulting

Regulated-Domain Consulting

Project-based engineering for medical, industrial, and IoT products where compliance and documentation carry as much weight as the design itself.

  • Requirements & architecture
  • Verification & traceability
  • Security & cryptographic review
  • Design history documentation
Tier 03 · Licensing

PQC FPGA IP

License a validated post-quantum cryptographic core — ML-KEM and ML-DSA on a single parametric datapath — as a drop-in block for your own hardware.

  • Parametric NIST levels 1/3/5
  • AXI4-Stream host interface
  • ACVP-validated conformance
  • Integration support included

Need government-funded R&D?

K-Fam is pursuing SBIR funding to productize its post-quantum FPGA accelerator. See the technical proposal summary and development roadmap.

Read the SBIR proposal →
◆ SBIR / STTR · TECHNICAL PROPOSAL

Unified Dual-Modulus PQC Accelerator

A single reconfigurable FPGA datapath that performs both NIST post-quantum key encapsulation (ML-KEM) and digital signatures (ML-DSA) — parametric across all three security levels, with a hardware-native Ethernet host interface.

FIPS 203 · ML-KEM FIPS 204 · ML-DSA FIPS 202 · Keccak/SHAKE Arty A7-100T AXI4-Stream over Ethernet

01 The Problem

Cryptographically-relevant quantum computers will break the RSA and elliptic-curve algorithms that protect today's industrial, medical, and defense communications. Adversaries are already harvesting encrypted traffic to decrypt later. NIST has standardized the replacements — but software implementations are too slow and too exposed for constrained, high-assurance embedded systems.

02 The Innovation

Most designs implement ML-KEM and ML-DSA as separate blocks, wasting fabric. K-Fam's core unifies them on a single dual-modulus arithmetic datapath with a shared Keccak engine — selectable at compile time across NIST levels 1, 3, and 5. The result is a smaller, cheaper, certifiable block that drops into existing designs.

03 Technical Maturity

This is not a concept. A working prototype runs on the Arty A7-100T with timing closed at 100 MHz, validated against NIST's ACVP test vectors, with documented constant-cycle side-channel hardening. The underlying research is peer-reviewed and published.

04 Commercial Dual-Use

The same core secures defense tactical radios, FDA-regulated medical telemetry, industrial wireless control, and critical infrastructure — any system facing a multi-decade service life and a federal post-quantum migration mandate.

◆ Technical Specifications

Target deviceXilinx Artix-7 (Arty A7-100T) — portable to larger parts
AlgorithmsML-KEM (FIPS 203) + ML-DSA (FIPS 204) on one datapath
HashingFIPS 202 Keccak / SHAKE, shared permutation engine
Security levelsParametric: ML-KEM 512/768/1024, ML-DSA 44/65/87 (compile-time select)
ClockTiming closure achieved at 100 MHz
Host interfaceEthernet AXI4-Stream (no UART bottleneck)
ValidationNIST ACVP conformance; byte-exact simulation; constant-cycle Decaps
Compliance postureFPGA is standalone FIPS 203/204 compliant; host only commands it

◆ Proposed Development Roadmap

PHASE I

Feasibility & Hardening

Harden the parametric core, complete full FIPS 203/204 conformance across all NIST levels, and demonstrate the standalone FPGA compliance boundary with a host-over-Ethernet reference design.

PHASE II

Productization & Integration

Port to production-grade FPGA/SoC targets, add formal side-channel evaluation, and package the core as a licensable, integration-ready IP block with a documented verification bundle.

PHASE III

Commercialization

Transition the validated core into defense, medical, and industrial platforms through IP licensing and integration support — K-Fam's Tier 03 engagement model.

◆ Why K-Fam

A veteran-owned small business led by a principal investigator whose doctoral research is this technology — not a team spinning up on an unfamiliar topic. The core already exists, is published, and is version-controlled in an open repository.

Veteran-Owned SAM.gov Registered 3 Peer-Reviewed Papers Active PhD Research (U. of Houston) Working Prototype
Discuss a teaming or funding opportunity →
About the Firm

A focused shop with deep roots.

MK

Mario Keh

FOUNDER · PRINCIPAL ENGINEER

Senior R&D electrical engineer and PhD candidate at the University of Houston, researching applied post-quantum cryptography in hardware. Mario's career spans firmware, hardware, systems, test, and PCB design across medical, industrial, and IoT products.

His research arc moves from software proof-of-concept through FPGA acceleration, side-channel hardening, and LLM-assisted security auditing — with work published in MDPI Electronics and IEEE venues.

  • Veteran-Owned Small BusinessSole proprietor; registered in SAM.gov under computer-engineering NAICS codes.
  • Based in Katy, TexasServing the Greater Houston area and remote clients nationwide.
  • Applied Research FocusPost-quantum cryptography hardware — FPGA, GPU, and side-channel analysis.
  • Markets ServedIoT, medical devices, and SaaS-connected hardware systems.
Get in Touch

Start a conversation.

Teaming on an SBIR, licensing the PQC core, or need embedded engineering help — send a note and Mario will respond directly.

Submitting opens your email client with the message pre-filled.

Emailyour-email@k-fam.com
LocationKaty, TX · Greater Houston Area
RegistrationsVeteran-Owned Small Business · SAM.gov registered
CapabilitiesFirmware · Hardware · Systems · Test · PCB · PQC FPGA IP